Black and White Chair | My Process + What NOT to do

Happy Friday! This week I was determined to finish reupholstering this chair and I did! (barely :)

This won't be a full tutorial, but my general process, my mistakes and what I'd do differently. Hopefully it will help someone avoid my mistakes :)

I started with this $9.99 chair from Goodwill. I knew that I didn't want to attempt the channeling, so I was planning on tufting instead. But it ended up not needing anything! (more on that later)

I tore off most of the foam and upholstery and spray painted the legs glossy black. I left the bottom cushion and one layer of fabric on for stability (I did layer a 1" piece of foam on top to make it extra cushy) 

Since the fabric (Sofia from Ikea) wasn't just a square, I took a large piece of paper roughly pushed it into the crevices, traced with a sharpie, and cut it out for my template.

I then used the template to cut my foam, (make sure that the foam is a little big, it crushes on the edges, you can always cut it down, but it generally works best a little big), batting (a little larger than the foam) and the fabric (larger than the batting)  *** make sure to cut it larger than you think you'll need. I cut mine almost too small in a few places and it made it hard to work with. You can always cut away the excess if needed.

I upholstered the seat first - it took a while, but it wasn't too bad .. the hardest part was working around the arms and the back supports. I kinda shoved the fabric down and pushed my stapler down between the cushion and arm so that the staples were hidden.

Moving onto the front of the back. I repeated the previous steps (template for foam, batting, fabric). I was having such a hard time getting everything somewhat smooth and tight because of the back supports (the legs ran all the way up). They were NOT easy to work around. ** If I was doing it again, I would have cut them off (in the opening between the back and the seat), pulled all of the fabric evenly/stapled (pulling up on the lower horizontal back support) and then reattached the supports (gluing and re bracing with a metal plate and screws). David ended up finishing up the part since I got too frustrated!! He's the best :)

We did add extra supports (made out of extra trim) so we could have the tufting in the center, but we didn't end up using them .. it got tight enough on it's own.

Here's another view of the support.

Next, we worked on the arms .. these were tricky to begin with, but even more difficult because of the stripes. Again, I got frustrated, so David helped with this too. We lined up the first black stripe - to get the fabric somewhat smooth, we couldn't make it all the way up the arm. So we cut it short and created a black stripe (ironed and folded under on the edges) out of the black fabric used for the cording and stapled in place. 

On the original chair, you could see the supports through the back so I added foam to hide them. 

On the back, for the arms, I didn't have enough fabric to make it to the end, so I pieced it together by lining up the stripe and sewing an extra piece on. Not ideal, but it worked. (after making two trips to Ikea for fabric, I wasn't going back :) Make sure to plan out all of your cuts and how you'll get it out of your fabric. When working with directional fabric, it's best to plan how you'll exactly use the fabric.

I stapled the back on and covered the staples with double cord welting (using Jenny's instructions) and glued in place with permanent fabric adhesive (be careful, it's stringy and will get everywhere). 

At this point, I started feeling a little better, it's amazing how finished it makes the chair look! You can use tape to help hold it in place if you'd like. 

To finish the edge I used an upholstery cardboard strip (thanks for the tip Julia!) and stapled in place. This gives a super crisp line!! Once done, I folded the fabric back down, stapled and covered with double cord welting. To avoid this extra step, I should have taken the seat cushion fabric all the way down, stapled, and covered with double cord welting. 

Finally, a few tips. Some are repeats from above, but important, so I'm listing them again :) 

1. Keep an iron handy. It helps to keep keep lines crisp and smooth out the fabric. 

2. Cut your fabric large, if it's too small it can be super tricky to work with - you can always cut it smaller.

3. Plan out how exactly how you'll reupholster the chair (plan your fabric cuts too) prior to starting. This one is tricky for me because I'm such a visual person, but I did make a fair amount of mistakes because I didn't plan well enough. 

Annabelle loves looking out the window here! I'm planning on making this coffee table into a bench (for the foot of our bed in MD but it will stay here for now since she loves it so much!) 

LOVE my new campaign chest found at goodwill! It's a little beaten up, but it shouldn't be too hard to fix. 

Finally, a few before and afters.

Such a transformation! Also, I was pleasantly surprised with the fabric from Ikea. It was a nice weight (similar to duck canvas), and looks like it should hold up nicely. 

I hope you have an amazing weekend!! Hopefully it warms up enough so I can spray paint (ok, it won't really be warm enough for a few months, but a little warmer than 0 degrees would be nice :) I'm SO excited to share my next project, it's a good one :)